txrollerchina

Tongxiang is a  conveyor equipment manufacturers china.Today we continue to share the belt conveyor common faults and preventive measures. 4.Reducer sound abnormalities This is caused by excessive wear and tear bearings and gears or housing loose screw loose, the treatment is to replace the bearing, adjusting the gap or replace the overall reducer overhaul. 5.Reducer warming too fast This is due to excessive fuel consumption, poor heat dissipation, reducer is buried by the source of coal, treatment is to adjust the oil, remove the source of coal. 6.Reducer leakage The reason is the ring is damaged, reducer cabinet with uneven surface, the counterpart bolt is not tight, the method is to replace the seal, tighten the box with the bearing surface and the bearing cap bolts. 7.Roller does not turn The reason is the roller bearing damage, rollers on both sides of the ring into the pulverized coal, blocked does not turn, so care roller too much bending force. Treatment ...

Bearings are an important part of the conveyor.The use of roller bearings in the course of its show a strong regularity, and repeatability is very good. Normal high-quality bearings in the beginning to use, the vibration and noise are relatively small, but some scattered spectrum, the amplitude is smaller, may be due to some manufacturing processes, such as surface burrs caused. After a period of exercise, the vibration and noise are maintained at a certain level, the spectrum is very simple, and only the first and second harmonic frequencies appear. Rarely appear more than three times the frequency spectrum above, the bearing condition is very stable, into a stable working period. Continue to run into late use, rolling bearing vibration and noise began to increase, and sometimes abnormal noise, but changes in vibration more slowly, this time, the bearing kurtosis value suddenly began to reach a certain value. In our opinion, the rolling bearing at this time is the initial failure. ...

Belt Conveyor Common Faults and Preventive Measures 1. Belt does not turn After starting the motor, the idler belt slides on the drive roller and the belt does not start up. Such failure is caused by insufficient belt tension, no adjustment of the tensioning device, excessive belt length, heavy load start, excessive tailpump stacking and other causes. 2. Belt deviation Deviation due to the belt in the operation of a lateral force generated by the lateral force for the following reasons: Conveyor loading on one side, rather than installed in the middle position; roller and roller installation axis and the center of the conveyor belt is not Vertical; inconsistencies in the level of the fuselage wire rope; conveyor joint is not correct, not straight; unloading drum position is not adjusted; tail drum, guide roller without adjustment can cause belt deviation. 3. Easy to disconnect the belt This is due to the belt tension is too large, the connector is not solid, the belt buckle poo...

What are the factors that affect the price of the conveyor roller ? What is the content of the price of the conveyor roller? 1.The material cost of the roller product In the cost price of conveyor roller, material cost occupies an important part, because we need to buy more materials during processing, and these materials directly affect the price of conveyor roller. 2. The technical cost of the roller product In the cost of roller, the cost of technology is also very critical. The product under modern professional technology is more guaranteed by quality and performance, so the price of such products will surely be high, which is also an inevitable trend. After all, the research and development of the new technology also needs more human, material and financial expenditure. 3. The cost of publicity cost of the roller products In the cost price of conveying drum in the promotional costs is not a small expenditure, and commodity economy, the competition is very fierce, in order to...

There are many kinds of conveyor equipment , which are mainly customized according to different actual needs. This is also the key factor that it can better adapt to the market. So what should we consider when the conveyor equipment  is designed and produced? First,under normal circumstances, we should design and select the most suitable material according to the complexity of the conveyor equipment and the actual application environment, so that it will not cause waste, but also can well meet the needs of use. Second, it is necessary to take full account of the effects of the characteristics of the conveyed goods on the conveyor equipment. Because the surface of the conveyer is in direct contact with the conveyor, the characteristics of the goods directly affect the selection of the conveyor equipment and the design of the system. The characteristics of the conveyed items include size, weight, surface characteristics (soft or hard), the rate of treatment, the way of packing and ...

Are you looking for conveyor equipment manufacturers in china?Hebei TongXiang Conveyor Machinery company is a good choice for you. Our company was founded in 1980,we specialized in conveyor equipment and accessories. Our products include conveyor roller and Idler, conveyor frame and station, pulley, Impact bar/bed and other components, such as rubber ring, tube, shaft, bearing seat and seal. CEMA,JIS, DIN, SABS, AS standards are available, as well as OEM service. If you need,please contact us at sales@txroller.com .